PCE-TAT 10 Adhesion Tester
Short Description:
Buy PCE-TAT 10 in Dubai, UAE at unbeatable prices! Discover top deals on the latest model here.
PCE-TAT 10 Adhesion Tester
The PCE-TAT 10 Adhesion Tester is a device designed to measure the adhesion strength of coatings on various substrates. This tool is essential for evaluating the bond quality of paints, coatings, and other surface treatments to ensure they adhere properly to the underlying material.
The pull-off type adhesion tester is designed to measure the adhesion strength of paints and other coatings on substrates as well as between layers or cohesive materials. This tensile adhesion tester is built in accordance with EN13144 and ISO 4624 standards.
The testing procedure with the mechanical tensile adhesion tester involves the following steps: A dolly is glued to the coating surface being tested. Once the glue has dried, the dolly is pulled off using the device’s spring system. The force applied to detach the glued dolly is displayed as a numerical value on the device’s scale, representing the adhesion strength.
PCE-TAT 10 Key Features
- Preparation for use
- Clean the surface of the measuring probe and the surface where you want to place the probe, for example, by using fine sand paper.
- Prepare the epoxy adhesive as instructed on the packaging and mix it thoroughly.
- If you use single-component super glue, open the tube.
- Apply the glue to the surface and place the measuring probe on the surface covered with glue, as described in more detail on the packaging.
- Operation
- Turn the top knob of the adhesion tester counter-clockwise to release the gripping mechanism and the spring.
- Â Now screw the adhesion tester (thread at the bottom) onto the measuring probe until the device reaches the surface to be tested.
- Â Turn the top knob clockwise until the measuring head is released from the test surface. You can read the tearing force from scale 1 or 2, depending on the measuring probe used.
- If the measuring probe has not been separated from the surface, turn the knob counter-clockwise to release the spring mechanism and remove the device from the measuring probe.
- Separate the measuring head from the surface, using a chisel and hammer.
- If the measuring probe has been separated from the surface, unscrew it from the device, using the wrench.
- Clean from the surface of the measuring probe any glue and paint residues or splinters.
PCE-TAT 10 Specifications
Technical specifications | |
Breakout force | 200 kg |
Diameter of base dolly, mm | 15.1 (â„– 1) and 19.5 (â„– 2) |
Specific breakout force, MPa | Dolly №1 up to 10 MPa (100) Dolly №2 up to 6 MPa (60) |
Scale, MPa | 1 (â„– 1) and 2 (â„– 2) |
Weight of adhesion tester, kg, no more | 1 |
Dimensions of adhesion tester, mm | 150×70 |
Dimensions of package, mm | L180*W150*H100 |
PCE-TAT 10
Technical specifications | |
Breakout force | 200 kg |
Diameter of base dolly, mm | 15.1 (â„– 1) and 19.5 (â„– 2) |
Specific breakout force, MPa | Dolly №1 up to 10 MPa (100) Dolly №2 up to 6 MPa (60) |
Scale, MPa | 1 (â„– 1) and 2 (â„– 2) |
Weight of adhesion tester, kg, no more | 1 |
Dimensions of adhesion tester, mm | 150×70 |
Dimensions of package, mm | L180*W150*H100 |
Rated 0 out of 5
0 reviews
Rated 5 out of 5
0
Rated 4 out of 5
0
Rated 3 out of 5
0
Rated 2 out of 5
0
Rated 1 out of 5
0
Be the first to review “PCE-TAT 10 Adhesion Tester” Cancel reply
You must be logged in to post a review.
Reviews
Clear filtersThere are no reviews yet.