Name: Buy Fluke FEV100 Electric Vehicle Charging Station EVSE Test Adapter
Brand: Fluke
SKU: 78352

Fluke FEV100 Electric Vehicle Charging Station EVSE Test Adapter

The Fluke FEV100 Electric Vehicle Charging Station EVSE (Electric Vehicle Supply Equipment) Test Adapter is an essential tool for professionals in the electric vehicle (EV) industry. Designed by Fluke, a renowned provider of testing and measurement equipment, the Fluke FEV100 Test Adapter is specifically tailored to ensure the safety, reliability, and compatibility of EV charging stations.

The EVSE charging cable may be damaged during use, increasing the risk of electric shock to the user. Stay protected and check for electrical shock hazards with a GFCI Trip Check. This function verifies that the EVSE circuit breaker is connected by detecting a ground fault. Additionally, pre-testing of the PE ground protection verifies that there is no hazardous voltage at the ground terminal.

Fluke FEV100 Key Features

Check protective earth for correct wiring and functioning with the PE pre-test feature.
Perform GFCI troubleshooting of EVSE and verify operation within safety standards.
Test charging states of EVSE with CP state simulation.
Verify charging voltage and maximum available current using a multimeter.
SAE J1772 compliant to North American standards.

Fluke FEV 100 Specifications

General specifications
Input voltage	UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 208 V, 60 Hz (three-phase system) or UL1/N = 120 V, UL2/N = 120 V, UL1/L2 = 240 V, 60 Hz (single-phase system), ±10% voltage fluctuations from nominal
EV connector (EVC-13)	SAE J1772 socket, 16 A (type 1, 5P single-phase)
Internal power consumption	2 W max.
Operating temperature	-4 °F to 104 °F (-20 °C to 40 °C)
Storage temperature	-4 °F to 122 °F (-20 °C to 50 °C)
Operating humidity range	10 % to 85 % relative humidity non-condensing
Storage relative humidity	0 % to 85 % non-condensing
Operating altitude	6561 ft (2000 m) max.
Dimensions (H × W × D)	Approx. 8.66 x 4.33 x 1.77 in (220 x 110 × 45 mm) without cable assembly
Weight	Approx. 4.4 lb (2 kg)
Safety standards	IEC 61010-1, Pollution Degree 2 IEC 61010-2-030
Measurement category	CAT II 250 V
IP protection class	IP54
Electromagnetic Compatibility (EMC)
International	IEC 61326-1: Basic Electromagnetic Environment CISPR 11: Group 1, Class A Group 1: Equipment has intentionally generated and/or uses conductively-coupled radio frequency energy that is necessary for the internal function of the equipment itself. Class A: Equipment is suitable for use in all establishments other than domestic and those directly connected to a low-voltage power supply network that supplies buildings used for domestic purposes. There may be potential difficulties in ensuring electromagnetic compatibility in other environments due to conducted and radiated disturbances. Caution: This equipment is not intended for use in residential environments and may not provide adequate protection to radio reception in such environments.
USA (FCC)	47 CFR 15 subpart B. This product is considered an exempt device per clause 15.103.
Functions
CP States	A, B, C, D
CP Error “E”	On/off
PE Error	On/off
GFCI Test	Yes, test resistor of 2 kΩ connected between L1 and PE, time limitation 40 ms
PE Pre-Test (typical)	Visible indication >30 V on PE conductor
Outputs (for test purpose only)
Measuring terminals L1, L2/N, PE	Max. 250 V 50/60 Hz, CAT II 250 V
CP signal output terminals	Approx. ±12 V (under normal conditions), in case of wrong wiring or error of the charging station these terminals can be hazardous ≥ max. 250 V against PE

Datasheet

Rated 0 out of 5

0 reviews

Rated 5 out of 5

Rated 4 out of 5

Rated 3 out of 5

Rated 2 out of 5

Rated 1 out of 5

Reviews

Clear filters

There are no reviews yet.

Be the first to review “Fluke FEV100 Electric Vehicle Charging Station EVSE Test Adapter”

You must be logged in to post a review.

Fluke FEV100 Electric Vehicle Charging Station EVSE Test Adapter