MOHAMMAD MAHDI Electronics Trading LLC
All Megger Products
Megger authorization
Call for price
The Megger VLF Sine Wave 62 kV is a portable true sine-wave very-low-frequency cable tester delivering 62 kVpeak for withstand and diagnostic testing of medium- and high-voltage cables, with automatic frequency control, a 7-inch touchscreen and optional tan-delta and partial-discharge diagnostics.
Call for price
The Megger Split-Box is a lightweight pipe and cable locator that traces buried water, gas, telephone, TV and power lines and measures their depth. Its separate transmitter and receiver operate at 126 kHz in inductive or conductive mode, with peak and null detection for fast, accurate tracing.
Call for price
The Megger BITE Receiver is a direct replacement receiver for the original BITE battery impedance test set, combining potential leads, a clamp-on current sensor and storage for 2000+ data sets (cell impedance, voltage and strap resistance) in one unit.
Call for Price
The Megger BITE3 determines the health of lead-acid cells up to 2000 Ah, measuring cell impedance, voltage, strap resistance, ripple and float current, with a built-in spectrum analyser and storage for over 1 million cell readings.
Call for price
The Megger MS2A is a lightweight portable primary injection test set delivering up to 240 A for testing overcurrent relays, moulded-case circuit breakers, thermal overloads and ground-fault devices, with a precision LED timer.
Call for price
The Megger MIT400/2 series are rugged CAT IV 600 V insulation and continuity testers with feedback-controlled test voltages, insulation resistance to 200 GΩ and a dual display with analogue arc, for electrical, industrial and maintenance testing.
Call for price
The Megger CHM series uses ultrasonic sound to measure the height of up to six overhead cables, with power models (CHM600/CHM600E) to 23 m and a telecom model (CHM2000), all accurate to typically better than 0.5%.
Call for price
The Megger EGIL is a single-breaker circuit breaker analyzer for timing, travel and coil-current testing of medium-voltage breakers, with a built-in printer and optional PC interface.
Call for price
The Megger MIT200 series are rugged pocket-sized insulation and continuity testers for electricians. Available with 250 V, 500 V and 1000 V test ranges (by model), they measure insulation to 1000 MΩ, continuity to 0.01 Ω with 200 mA, plus AC/DC voltage — all in a compact CAT III 600 V instrument.
Call for price
Megger CABA Win (Computer-Aided Breaker Analysis) is benchmark circuit-breaker analysis software that organises test tasks, ensures consistent measurements, stores results and generates reports for Megger TM1800, TM1700, TM1600/MA61 and EGIL analysers.
Call for price
The Megger Teleflex VX is a high-performance cable fault prelocation reflectometer (TDR) for power cables. Supporting three-phase TDR, arc reflection, ICE and decay methods over ranges up to 1280 km with 400 MHz sampling, it delivers precise fault prelocation on a large 15-inch colour display.
Call for price
The Megger T3090 is a versatile time domain reflectometer and cable fault locator for power cables. Combining classic low-voltage TDR with high-voltage arc-reflection (ARM) and optional surge modes over ranges up to 100,000 ft, it displays clear reflectograms on a bright 10.4-inch colour screen.
Call for price
The Megger KMK8 is a handheld bridge and TDR instrument for telecommunication cable evaluation and fault location, combining active/passive bridges with reflectometry.
Call for price
The Megger FC3 Fault Converter is a reflectometer add-on that makes humidity and wet faults visible on a TDR — especially in communication cables — using a switchable DC offset.
Call for price
The Megger ICMmonitor CA is a fully computer-controlled partial discharge (PD) monitor for MV and HV insulation, building phase-resolved 3D PD patterns via a virtual-instrument interface.
Call for price
The Megger ICMcompact is a compact, stand-alone digital partial discharge (PD) detector for evaluating MV and HV insulation, widely used in manufacturing QA/QC and adaptable to field testing.
Call for price
The Megger B10E is a compact circuit-breaker test power supply with a continuously variable 24–300 V DC / 24–260 V AC output and separate close-coil, trip-coil and spring-charging-motor outputs, plus direct triggering for minimum trip-voltage testing.
Call for price
The Megger PD LOC is a partial discharge locator that pinpoints PD faults in medium-voltage cables using impulse-reflection (TDR) analysis. Working across PE/XLPE, PILC, EPR and mixed networks, it uses a portable PD-TX transmitter and Teleflex SX receiver to calculate the exact distance to the discharge source.
Call for price
The Megger Teleflex SX-1 is a portable cable fault prelocation reflectometer (TDR) with a 10.1-inch sunlight-readable touchscreen. Supporting TDR, arc reflection, ICE and decay methods over ranges to 160 km with 400 MHz sampling and 96 dB dynamic range, it pinpoints faults quickly and accurately.
Call for price
The Megger VLF CR-60HP and VLF CR-80 are high-power cosine-rectangular VLF cable test systems (60 and 80 kVrms) that deliver very high test power without frequency reduction, allowing all three phases of long MV/HV cables to be tested at a standard 0.1 Hz, plus DC and sheath fault testing.
Call for price
The Megger VLF CR-28 is a portable cosine-rectangular very-low-frequency cable test system rated to 28 kVrms, combining VLF withstand, DC and sheath fault testing in one instrument for medium-voltage cables up to the 15 kV class.
Call for price
The Megger VLF Sine Wave 62 kV test and diagnostic system is a portable true sine-wave very-low-frequency platform delivering 62 kVpeak for withstand testing and, with optional tan-delta and partial-discharge modules, full condition assessment of medium- and high-voltage cables.
Call for price
The Megger VLF Sine Wave 45 kV is a portable true sine-wave very-low-frequency cable tester delivering 45 kVpeak for withstand and diagnostic testing of MV cables, with automatic frequency control, a 7-inch touchscreen and optional tan-delta and partial-discharge diagnostics.
Call for Price
The Megger MTDR300 is a three-phase time domain reflectometer (TDR) for fast cable fault location on power and communication cables. With three simultaneous TDR channels, a large XGA display and arc-reflection capability, it lets engineers compare phases and pinpoint faults quickly across ranges up to 55 km.
Call for price
The Megger (Seba) Overhead Line Testing System uses time-domain reflectometry to locate faults and impedance irregularities on de-energised overhead lines up to 1000 km. It pinpoints breaks, short circuits, branch-offs and smaller defects such as poor connections, faulty insulators and in-growing trees.
Call for price
The Megger VLF Sine Wave 34 kV is a portable true sine-wave very-low-frequency cable tester for withstand and diagnostic testing of medium-voltage cables, delivering 34 kV at 0.1 Hz with a 5 uF test capacity and optional tan-delta and partial-discharge diagnostics.
Call for price
The Megger UHF PD Detector is a handheld, dual-channel online partial-discharge surveying system for MV and HV substations, using UHF, TEV and HFCT sensors with a phase-resolved PD display to find developing insulation faults without an outage.
Call for price
The Megger PVS100i is a GPS-synchronised phase verification system that positively matches phases across distribution networks without a direct connection between measuring points. Using two units — a reference base station and a mobile unit — it compares phase angles from 400 V up to 120 kV for safe switching and load balancing.
Call for price
The Megger PD Scan is a lightweight handheld partial discharge scanner for early detection of PD in medium- and high-voltage equipment. It combines TEV, airborne ultrasonic and HFCT measurement in one instrument with a touchscreen, camera and QR scanner for fast, documented surveys of switchgear and cables.
Call for price
The Megger PDS 60-v2 is a portable partial discharge detection and localisation system for medium- and high-voltage cables and accessories up to 60 kV. It works with VLF, DAC and cosine-rectangular sources, giving real-time PRPD analysis to distinguish corona from internal PD and pinpoint defects.
Call for price
The Megger ARM 3-E is an arc-reflection stabilising unit for cable-fault prelocation, connecting a surge generator to a time-domain reflectometer so that high-resistance and flashing faults can be pinpointed using the Arc Reflection Method (ARM).
Call for price
The Megger CARLOC utility locating system combines intelligent signal processing with flexible operating modes to trace buried cables and pipes quickly and accurately, in an IP65, −20 to 50 °C rugged transmitter/receiver pair.
Call for price
The Megger PDS 62-SIN is a portable partial discharge detection and localisation system with an integrated VLF sinusoidal coupling unit, rated to 62 kV peak. Compliant with IEC 60270, it measures PD from 2 pC, localises defects over cable lengths up to 16 km, and gives real-time PRPD analysis.
Call for price
The Megger HV DAC series is a compact, transportable damped-AC test and diagnostic system for high-voltage cables, for after-laying testing and condition assessment on runs up to 32 km.
Call for price
The Megger TDS NT is an all-in-one cable test and diagnosis system that combines VLF withstand testing, tan delta (DAC) diagnostics and partial-discharge measurement with PD mapping in one platform. Available in 40 kV and 60 kV versions, it tests, diagnoses and locates faults on MV cables.
Call for price
The Megger TDM45 is a high-power test and diagnosis combination for medium-voltage cables up to 45 kV. It brings VLF (sine and cosine-rectangular), DC and sheath testing together with tan delta and partial-discharge diagnostics, testing and assessing MV cables up to 20 km in a modular, portable system.
Bench Multimeters